Video Gallery — Factory, Process & Testing Videos
Explore Domi Refrigeration’s video resources for factory environment, manufacturing process, leak testing, quality inspection and customer visit documentation. These videos help global buyers understand our production and validation workflow before starting a project.
✓
Factory and production video resources
✓
Manufacturing process visibility
✓
Testing and inspection video support
✓
Buyer visit and audit documentation upon request
Browse by Video Category
All video content below is organized by production and quality category. Video placeholders are reserved — the client team should upload actual recorded footage to each slot. No videos have been fabricated or artificially generated.
🏭
Factory VR Tour
Factory environment overview, production area layout, equipment distribution and general manufacturing facility documentation.
🔥
Welding Process
Welding operation video for heat exchanger components, showing tube-to-header connections, brazing and joint preparation.
🔬
Helium Leak Testing
Leak detection process video showing test setup, helium introduction, pressure holding and detection equipment for heat exchanger quality validation.
👥
Customer Factory Inspection
Documentation of customer or third-party factory audits, incoming inspection visits and on-site quality review processes.
⚙
Manufacturing Process
Step-by-step production videos covering tube bending, fin assembly, header fabrication, coil assembly and component handling.
✅
Quality Inspection
Visual inspection, dimensional check, pressure test, surface review and outgoing quality control process documentation.
Featured Video Resources
⚠ All video slots below are placeholders — client must upload real, verified video content
No videos have been fabricated or AI-generated. Each card shows where a real video will be embedded after client upload.
▶
VIDEO PLACEHOLDER — CLIENT TO UPLOAD
FACTORY VR TOUR
Factory Overview Video [PLACEHOLDER — REAL VIDEO REQUIRED]
A factory tour video showing production areas, equipment layout, material handling zones and general manufacturing environment. This placeholder is reserved for an actual recorded factory walk-through video. [REQUIRES CLIENT VERIFICATION]
⚠ PLACEHOLDER — REAL VIDEO REQUIRED
▶
VIDEO PLACEHOLDER — CLIENT TO UPLOAD
WELDING PROCESS
Welding Process Video [PLACEHOLDER — REAL VIDEO REQUIRED]
Welding operation footage showing tube-to-header connection processes, brazing operations and joint preparation for heat exchanger assemblies. Client to upload actual welding process video. [REQUIRES CLIENT VERIFICATION]
⚠ PLACEHOLDER — REAL VIDEO REQUIRED
▶
VIDEO PLACEHOLDER — CLIENT TO UPLOAD
HELIUM LEAK TESTING
Helium Leak Testing Video [PLACEHOLDER — REAL VIDEO REQUIRED]
Leak test demonstration showing helium introduction, pressure holding, detection equipment and test result review for heat exchanger and refrigeration coil quality control. Client to provide and upload verified leak testing footage. [REQUIRES CLIENT VERIFICATION]
⚠ PLACEHOLDER — REAL VIDEO REQUIRED
▶
VIDEO PLACEHOLDER — CLIENT TO UPLOAD
CUSTOMER INSPECTION
Customer Factory Inspection Video [PLACEHOLDER — REAL VIDEO REQUIRED]
Factory audit or inspection visit documentation. This slot is reserved for verified customer or third-party inspection visit footage. Do NOT upload footage without customer approval. [REQUIRES CLIENT VERIFICATION]
⚠ PLACEHOLDER — REAL VIDEO REQUIRED
Video Content by Category
Select a category to see what video content is planned for each section. All slots are placeholders — client to upload verified, recorded video footage to each category.
Factory Tour Video — What to Expect
- ▶Production area layout and equipment placement
- ▶Material input, in-process storage and finished goods areas
- ▶Manufacturing environment and facility overview
- ▶Equipment condition and workshop organization
⚠ PLACEHOLDER — Client must upload actual factory tour or VR footage. This content has not been fabricated. [REQUIRES CLIENT VERIFICATION]
Welding Process Video — What to Expect
- ▶Tube-to-header connection and brazing operations
- ▶Welding fixtures, jig setup and joint preparation
- ▶Welding parameter and process control visibility
- ▶Post-weld inspection and visual check process
⚠ PLACEHOLDER — Client must upload actual welding process video footage. No welding footage has been created or simulated. [REQUIRES CLIENT VERIFICATION]
Helium Leak Testing Video — What to Expect
- ▶Leak test equipment setup and fixture connection
- ▶Helium introduction and pressure holding process
- ▶Detection equipment use and sensitivity demonstration
- ▶Test result review and pass/fail documentation
⚠ PLACEHOLDER — Client must upload actual helium leak test demonstration footage. No helium test video has been fabricated or AI-generated. [REQUIRES CLIENT VERIFICATION]
Customer Factory Inspection Video — What to Expect
- ▶Third-party or customer audit visit documentation
- ▶Incoming inspection and on-site quality review footage
- ▶Factory environment review by visiting buyer team
- ▶Production area access and process visibility documentation
⚠ PLACEHOLDER — Do NOT upload customer inspection footage without confirmed customer approval. Any customer name or company reference must be verified before publishing. [REQUIRES CLIENT VERIFICATION]
Manufacturing Process Videos — What to Expect
- ▶Tube bending, fin stamping and header fabrication process
- ▶Coil assembly, positioning and component handling
- ▶Multi-pass production workflow and workstation sequence
- ▶Material flow and process control at each production stage
⚠ PLACEHOLDER — Client must upload actual manufacturing process footage. No process video has been created or AI-generated. [REQUIRES CLIENT VERIFICATION]
Quality Inspection Videos — What to Expect
- ▶Visual inspection, dimensional check and surface review
- ▶Pressure test setup and hold process documentation
- ▶Outgoing quality control and packaging inspection
- ▶Inspection record review and non-conformance handling
⚠ PLACEHOLDER — Client must upload actual quality inspection footage. No inspection video has been fabricated or AI-generated. [REQUIRES CLIENT VERIFICATION]
How to Request Video Access
Some video content may be shared on a per-request basis depending on the project stage, NDA status or buyer relationship. Use the steps below to request specific video resources.
1
Submit Video Request
Use the inquiry form below or contact the Domi team directly. Specify which video category or process you would like to review.
2
Project Context Review
The Domi team will review your request and confirm which video content is available for your project scope and stage.
3
Video Access Provided
Relevant video links, shared files or live video call arrangements will be confirmed based on availability and project requirements.
Frequently Asked Questions — Video Gallery
Request Video Access or Schedule a Factory Video Call
Contact the Domi Refrigeration team to request specific video resources, ask about live factory video call availability, or submit your project background for a customized factory documentation review. All video content shared is real recorded footage — no AI-generated or fabricated material.